Thermaline Series of CTP Plate Processors have been manufactured incorporating the most up to date electronic techniques available. The complete functions of the machine are controlled from one single touch screen control.

The sleek design enables the smallest footprint available for this type of processor. Automatic start-stop saves on power, even the rewash/regum has automatic start/stop.

 Two brushes in the developer ensure correct clearance of the plate. The brushes also have adjustable speed control, independent of the plate speed. There is also a brush in the wash section making sure that the plate is clear of all chemistry before gumming.

Other benefits are filtering of developer, Auto Fill with Auto Level stop, replenishment by plate area, anti-oxidation, Auto Gum Wash and periodic movement of rollers during standby mode. These are but a few of the useful operations controlled by the microprocessor.

Click for Specifation

  Touch screen adjustments are so easy to understand, eliminating 

  mistakes. No knobs or dials to confuse you or accidentally get misaligned

Roller configuration for full series

Easy release of all rollers for cleaning. No tools are needed

MACHINE SPECIFICATIONS

• 4 sections:  developing, rinsing, gumming and drying

• Microprocessor PLC (Programmable Logical Controller) with touch-screen display

• High speed developer tank auto-fill

• Adjustable developing time displaying seconds in developer

• Automatic and adjustable developer replenishment (in cm/m²) according to the actual plate size

• Separate anti-ox replenishment setting options (in cm/m²)

• “Week-end” replenishment programme (in cc per hour of machine in “sleep” mode)

• Adjustable developer temperature, controlled through chiller unit and heating element

• “Sleep” mode, with periodic rollers movement and automatic start-up of the machine at the time set (through internal clock)

• 1 bristle brush in the developing section (with adjustable independent speed and pressure calibration)

• Immersed rollers set for small sized plates

• Developer filter

• 1 bristle brush in the rinsing section

• Low level control for the developer

• Empty replenisher cans alarm (developer and gum)

• Adjustable gumming time, with gum recirculation through the origin can

• Two dryer temperature settings

• Plate counter (partial and total) and working hour-meter

• “Stand-by” programme, with periodic rollers movement and gum rollers reconditioning

• 2^nd entry slot for re-washing and re-gumming, with automatic start

• Motor reverse function

DownLoad Leaflet

SPECIFICATIONS

Thermaline 90

Thermaline 120

Thermaline 155

Thermaline 180

Maximum plate width (mm)

860

1160

1500

1720

Minimum plate length (mm)

320

320

320

320

Plate thickness (mm)

.15-.50

.15-.50

.15-.50

.15-.50

Transport speed (Dev. Time)

12-90 seconds

12-90 seconds

12-90 seconds

12-90 seconds

Dev. Tank capacity (Litre.)

45 litres

60 litres

75 litres

90 litres

Water Inlet

18mm washing machine connection

Water drain (inner dia.)

40mm

Electrical requirements

30amp single phase

Net weight (Kg.)

450 Kg

500 Kg

600 Kg

700 Kg

Optional equipment for all Thermaline Plate Processors:

On customer’s request, the machine can be equipped with the following options:

• 2^nd bristle brush in the developing section (recommended for negative plates)

• Water recirculating units: 70 litres – 120 litres

• Conductivity meter with inductive probe to check the developer efficiency, with values (in mS) displayed on the main screen

• Interface board with the CTP

• Jam detect device (output sensor)

• Automatic gum section cleaning device

• Drip tray

• Input table for offline work

• Output table for offline work

• Plate stacker with adjustable transport speed

• Conveyor for the plate transport from the CtP to the processor

• Remote diagnostic system via modem

• Dedicated software to control the machine via PC

CTP PLATE PROCESSORS

PROGRESS SERIES OF PLATE PROCESSORS

PLATEPRO 460 TABLETOP PLATE PROCESSOR

VISIBLE LIGHT RANGE FOR AGFA PLATE MATERIAL

CONVENTIONAL PLATE PROCESSORS

PHOTOPOLYMER CTP PLATE PROCESSOR

For information, quotations and advice please

  click here    

Website Designed By Richard Foley